Skip to main content

Failure investigation, remedies, and mitigation of a centrifugal pump.

 BY LUIS INFANTE & RODOLFO ALVARADO.

A high energy pump at a water injection station in El Furrial, Venezuela exhibited extremely high vibration levels prior to an overhaul. It then suffered a catastrophic failure during startup following overhaul. The hydrodynamic bundle, rotor, and drive end (DE) bearing suffered damage.

 


High energy pump for boiler feed water. Courtesy of Flowserve.

This centrifugal pump is a 3,000 HP, double-case volute, boiler feed water pump type. It has nine stages, outputs 750 gpm of water with suction pressure 1800 psi and discharge pressure 5250 psi. Rated speed was increased from 6000 to 6600 RPM to enhance the hydraulic performance. However, the pump’s actual discharge pressure was about 4,500 psi, well below the target value of 5,000 psi. The coupling was reportedly poorly fitted.

The increased RPM created rotordynamic concerns of getting closer to a critical speed, thus the operator wanted to know about the synchronous regime. The operator also wanted remedial measures and temporary mitigation steps to keep the pump running for 4-6 months until remedies were finally enforced.

The course of action for this investigation was clear since the beginning: conduct an internal clearances analysis and a forced response rotordynamic study.

A thorough study of internal clearances was conducted. Table 1 shows the results from this study featuring a comparison between internal (hydrodynamic bundle) clearances from different data sources, namely: design data, shop measurements, API-610 minimum clearances, and typical clearances for a similar pump with vibratory problems. As a result, the recommended clearance for the center seal, balance piston, eye, and impeller hub seals are shown in the bottom part of Table 1.

Due to the high vibration levels (20 mil DE, 5 mil NDE) reported before the overhaul, a simulation of the pump’s forced response rotordynamic behavior was attempted using a trial unbalance weight located in the coupling. A mass-elastic mathematical model incorporating the effect of the internal seals at 1X and 2X design clearance (as suggested by API 610) was used for this purpose.

One can expect a flexible rotor behavior (first critical speed below operating speed) for this high-speed, long slender shaft, but the stiffening effect provided by the internal seals (Lomakin’s effect) locates the first critical speed in the vicinity of 9,000 RPM, well above 6,600 RPM operating speed. Retrofitting the bearing and coupling with the technology presented below raises this first critical speed to approximately 10,000 RPM, thus discarding the likelihood for resonance despite the steep vibration plot obtained during a ramp up vibration survey.

 


Table 1: Analysis of internal clearances.

REMEDIES AND MITIGATION

Our attention was focused on balancing and the effect on the dynamic stability of the rotor-bearing-support substructure. A bearing and coupling retrofit was recommended with a balancing plane on the coupling and an added mass on the bearing housing. It was discovered that the shaft was excessively long on the DE. Shortening the shaft together with a reduced moment coupling proved to be beneficial in keeping rotor synchronous response away from resonances. Such coupling design has a center of gravity and flex discs moved closer to the bearing.

Tilting pad bearing is a good option for stability and support of this slender high-speed shaft. A pad load distribution analysis showed increased clearances unloading the top pads and the six-pad arrangement offered the best support. Furthermore, a lateral stability analysis revealed six-pad bearing to have the best stability parameters (whirl mode, log dec, amplification factor, undesirable speeds).

Effective mitigation measures that ran for a few months with acceptable vibration levels turned out to be:

1.      Add 150lb to the bearing housing.

2.      Increase internal clearances and bearing clearances (max 6 mil).

3.      Finning the bearing housing ribs for enhanced heat dissipation.

4.      Using the coupling as a balancing plane; adjusting and balancing the coupling.

5.      Correct bearing housing distortion.

CONCLUSIONS

The most likely cause of failure was attributable to tight clearances found in the hydrodynamic bundle’s internal seals. OEM design and even API clearances were considered to be too tight. Reducing internal clearances below API 610 recommendations exposes these pumps to catastrophic failures during start up. For the impeller eye, we recommend a 50% increase (to 27 mil) over API values for stages 1–4 and a 25% increase (to 23 mil) for stages 5–9. Clearances for other rotor locations are shown in Table 1.

Trimming the shaft in the DE side and installing a reduced moment coupling helps in separating the operating speed from the first critical envelope, thus reducing the amplitude of vibration.

 

Source: turbomachinerymag

 

Labels:

Comments

Post a Comment

Popular posts from this blog

Why Pump Shafts Often Break at the Keyway Area

By NTS Pump shaft failure can lead to significant downtime and repair costs in industrial plants. One of the most common locations for pump shaft failure is at the keyway area. In this article, we will explore the reasons why pump shafts often break at the keyway and what can be done to prevent such failures. The keyway is a high-stress point (weakest point)  on the shaft, where a key is inserted to transmit torque between the shaft and the pump impeller or coupling. During operation, the keyway experiences cyclic loading that creates a bending moment in the shaft, which is concentrated in the keyway area. Over time, this cyclic loading can cause fatigue failure in the shaft material, leading to a fracture at the keyway. In addition to cyclic loading, other factors can contribute to shaft failure at the keyway. Improper keyway design or installation can lead to stress concentrations or inadequate clearance between the key and keyway . Misalignment or overloading can also cause ex...
Post a Comment
[Read more...]

Top 8 Reasons for Mechanical Seal Failure and How to Prevent Them

Mechanical seals are critical components of pumps, responsible for maintaining a fluid-tight seal between the rotating shaft and the stationary pump housing. However, these seals can fail due to various factors, leading to leakage, reduced pump efficiency, and costly downtime. In this article, we will discuss the top reasons for mechanical seal failure in pumps and how to prevent them. 1-Improper Seal Selection Choosing the wrong mechanical seal can cause it to fail. Consider the following factors that can contribute to seal failure: • Chemical compatibility: All seal components, such as the seal faces and O-rings, must be compatible not only with the process fluid being pumped, but also with non-process fluids used for cleaning, steam, acid, and caustic flushes, etc. • Physical degradation: Using soft seal faces on abrasive liquids will not last. Shear-sensitive liquids, like chocolate, can break down and leave behind solids (such as cocoa powder) and force out liquids (like oil). • S...
Post a Comment
[Read more...]

What is ISFD Bearings, how it works?

What is the ISFD Bearings? Integral squeeze film damper  ( ISFD) technology, a Flexure Pivot tilt pad journal bearing, provides precise stiffness and damping to increase the dynamic stability of the rotor/bearing system. Reduce Dynamic Bearing Forces ISFD technology reduces the dynamic load that is transmitted to the bearings, which reduces pedestal vibration and increases bearing life, particularly for rolling element bearings. For fluid film bearings, the technology can mitigate pivot wear and reduce babbitt fatigue. Decrease Unbalance Sensitivity ISFD technology helps reduce the sensitivity to unbalance, protecting impellers and seals from rubbing and increasing maintenance intervals. Versatile Design The ISFD design, manufactured through electrical discharge machining (EDM), can integrate the bearing and damper into one unit for a space-saving solution suitable for new and retrofit installations. ISFD technology can be used with tilt pad, Flexure Pivot tilt pad, fixed profile o...
Post a Comment
[Read more...]

Preventing Motor Bearing Damage from Shaft Current with the AEGIS® Ring

Electric motors are the workhorses of modern industry, powering everything from pumps and fans to conveyor belts and heavy machinery. But these vital components are not immune to wear and tear, and one common problem that can lead to premature motor failure is bearing damage caused by shaft current. Shaft current is a type of electrical discharge that occurs when there is a voltage potential between the motor shaft and the bearing, resulting in the flow of electrical current through the bearing. This current can cause a range of problems, including pitting and fluting of the bearing surfaces, which can lead to premature wear and failure. Shaft current Motor shaft current can have several harmful effects on bearings, including: 1.      Bearing pitting and fluting: Electrical discharges can cause tiny pits and flutes to form on the bearing surfaces, leading to premature wear and failure. 2.       Bearing noise and vibration: Shaft current can cause ...
Post a Comment
[Read more...]

Journal Bearings and Their Lubrication

J ournal or plain bearings consist of a shaft or journal which rotates freely in a supporting metal sleeve or shell. There are no rolling elements in these bearings. Their design and construction may be relatively simple, but the theory and operation of these bearings can be complex. This article concentrates on oil- and grease-lubricated full fluid film journal bearings; but first a brief discussion of pins and bushings, dry and semilubricated journal bearings, and tilting-pad bearings. Low-speed pins and bushings are a form of journal bearing in which the shaft or shell generally does not make a full rotation. The partial rotation at low speed, before typically reversing direction, does not allow for the formation of a full fluid film and thus metal-to-metal contact does occur within the bearing. Pins and bushings continually operate in the boundary lubrication regime. These types of bearings are typically lubricated with an extreme pressure (EP) grease to aid in suppo...
Post a Comment
[Read more...]